Fuse issue

Munaro · May 10th, 2010, 15:04

Alright so my fuse blew in my M4 its a small 20 amp glass fuse, locally I cant find this fuse. Someone told me that its fine to direct wire them, just as an added chance of frying motor. My question is thoughts on direct wiring? or dose anyone know where to find that fuse? for Locals I have tried, source and SMI and some other place by SMI.

Crunchmeister · May 10th, 2010, 15:07

You can get this fuse at any automotive supply store, Cdn Tire, and many other sources.

And yes, you can direct wire. However, I would make sure there's nothing wrong with the gun before removing the fuse and hard-wiring it.

VooDooPeteK · May 10th, 2010, 15:08

You don't need the fuse but if you decide to bypass it you will just need to be more careful when playing with that gun.

I know a bunch of people that the first thing they do when they get a new gun is remove the fuse.

It is safer running the gun with a fuse but not needed thats for sure

Crunchmeister · May 10th, 2010, 15:13

What Voodo said is correct for the most part. However, to expand on my original reply, usually, a fuse blows where there's an electrical problem with the gun. Sometimes, it can be just because you overheated the fuse with sustained full auto, but generally, if you blew a fuse, there's something wrong in the gun. Bypassing the fuse when there's an electrical problem already present is not a good idea.

Jimski · May 10th, 2010, 15:17

yeah, you just need to know if the fuse blew because it was crap, or pre-broken as I've seen before, or because the gun has a problem ( mechbox seizing, short-circuit...)

chaosnemesis · May 10th, 2010, 15:20

In short, if you have to ask... then you'll need it. Once you're more familiar with the internals and how they work , you can decide whether or not to bypass the fuse.

Cantire sells the fuses in the automotive dept. you can use the 32V20A fuses if they're out of the 250's.

andrew321 · May 10th, 2010, 16:21

All my guns except my AUG have been straight wired, no fuses.. never had an issue. With s-system and AK-wth-huge-battery I had to remove them to make it fit.

You can also wire it with a higher quality blade automotive fuse (change the holder as well) if I am correct?

My GBBR came pre wired without a fuse

.

flack · May 10th, 2010, 16:28

No fuse is not too risky as long as you stop pressing the trigger if your mechbox seize.

If you pull the trigger and nothing happens, STOP AND FIND THE PROBLEM or youll fry your motor.

Con Murder · May 10th, 2010, 16:59

Before anything, op, check your wireing as the fuse was blown for a reason. Usually (especially if the gun is new) the problem is a wire that has been exposed. Check all wires for breakage and exposed wire, especially at places they bend or could get pinched. Electrical tape will seal and stop the short, replace fuse (I just grabbed a bus pack of 4 or five) and test again until its all good.

PS
If you play near, around or in water don't remove the fuse!

Munaro · May 10th, 2010, 21:33

Thanks guy, your always super helpful. If i can find the fuse i'll stick with the fuse, if not i'll direct wire. I just picked up an ICS L85, it has a blade fuse, so I may add one of those in instead on the M4

Munaro · May 12th, 2010, 12:13

I solved my issue by changing the glass fuse out for a blade fuse, worked great.

Kos-Mos · May 12th, 2010, 15:15

Quote:

Originally Posted by Con Murder

Before anything, op, check your wireing as the fuse was blown for a reason. Usually (especially if the gun is new) the problem is a wire that has been exposed. Check all wires for breakage and exposed wire, especially at places they bend or could get pinched. Electrical tape will seal and stop the short, replace fuse (I just grabbed a bus pack of 4 or five) and test again until its all good.

PS
If you play near, around or in water don't remove the fuse!

Don't you know that your AEG CAN AND WILL work completely wet?

A DC electric system will work no problem. As long as the BATTERY is not soaked, the motor can run underwater.
We are talking about a DC 8-12v 10A system... not an AC 120V 15A...

Want proof? Check youtube for "electric motor break-in" and see what we do in R/C with our motors.

Crunchmeister · May 12th, 2010, 15:26

Quote:

Originally Posted by Con Murder

If you play near, around or in water don't remove the fuse!

You should really not comment about stuff you have no idea about.

CJay · May 12th, 2010, 16:07

They're correct. Dc circuits will run fine under water provided the battery is not wet ad ur using sub 50V power supply. On the other hand I'd love to see an aeg on 120v haha.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

May 10th, 2010, 15:04	#1
Munaro Trader rating Join Date: Apr 2010 Location: Langley B.C	Fuse issue Alright so my fuse blew in my M4 its a small 20 amp glass fuse, locally I cant find this fuse. Someone told me that its fine to direct wire them, just as an added chance of frying motor. My question is thoughts on direct wiring? or dose anyone know where to find that fuse? for Locals I have tried, source and SMI and some other place by SMI. __________________ M4, L85, Mp5, Scar, Sig 552, M14

May 10th, 2010, 15:07	#2
Crunchmeister Trader rating Join Date: Nov 2007 Location: In your bedroom going though your underwear drawer	You can get this fuse at any automotive supply store, Cdn Tire, and many other sources. And yes, you can direct wire. However, I would make sure there's nothing wrong with the gun before removing the fuse and hard-wiring it. __________________

May 10th, 2010, 15:13	#4
Crunchmeister Trader rating Join Date: Nov 2007 Location: In your bedroom going though your underwear drawer	What Voodo said is correct for the most part. However, to expand on my original reply, usually, a fuse blows where there's an electrical problem with the gun. Sometimes, it can be just because you overheated the fuse with sustained full auto, but generally, if you blew a fuse, there's something wrong in the gun. Bypassing the fuse when there's an electrical problem already present is not a good idea. __________________

May 10th, 2010, 15:08	#3
VooDooPeteK Trader rating Join Date: Feb 2010 Location: Thorold, Ont	You don't need the fuse but if you decide to bypass it you will just need to be more careful when playing with that gun. I know a bunch of people that the first thing they do when they get a new gun is remove the fuse. It is safer running the gun with a fuse but not needed thats for sure

May 10th, 2010, 15:17	#5
Jimski Trader rating Join Date: Jun 2005 Location: Montreal	yeah, you just need to know if the fuse blew because it was crap, or pre-broken as I've seen before, or because the gun has a problem ( mechbox seizing, short-circuit...) __________________

May 10th, 2010, 15:20	#6
chaosnemesis Trader rating Join Date: Nov 2008 Location: Toronto	In short, if you have to ask... then you'll need it. Once you're more familiar with the internals and how they work , you can decide whether or not to bypass the fuse. Cantire sells the fuses in the automotive dept. you can use the 32V20A fuses if they're out of the 250's.

May 10th, 2010, 16:21	#7
andrew321 Trader rating Join Date: May 2007 Location: Winnipeg, MB	All my guns except my AUG have been straight wired, no fuses.. never had an issue. With s-system and AK-wth-huge-battery I had to remove them to make it fit. You can also wire it with a higher quality blade automotive fuse (change the holder as well) if I am correct? My GBBR came pre wired without a fuse .

May 10th, 2010, 16:28	#8
flack Trader rating Join Date: Jan 2005 Location: St-Bruno	No fuse is not too risky as long as you stop pressing the trigger if your mechbox seize. If you pull the trigger and nothing happens, STOP AND FIND THE PROBLEM or youll fry your motor.

May 10th, 2010, 16:59	#9
Con Murder Trader rating Join Date: May 2009 Location: Lethbridge Alberta Canada	Before anything, op, check your wireing as the fuse was blown for a reason. Usually (especially if the gun is new) the problem is a wire that has been exposed. Check all wires for breakage and exposed wire, especially at places they bend or could get pinched. Electrical tape will seal and stop the short, replace fuse (I just grabbed a bus pack of 4 or five) and test again until its all good. PS If you play near, around or in water don't remove the fuse! __________________ Con Murder Dark Rhino L.A. Airsoft

May 10th, 2010, 21:33	#10
Munaro Trader rating Join Date: Apr 2010 Location: Langley B.C	Thanks guy, your always super helpful. If i can find the fuse i'll stick with the fuse, if not i'll direct wire. I just picked up an ICS L85, it has a blade fuse, so I may add one of those in instead on the M4 __________________ M4, L85, Mp5, Scar, Sig 552, M14

May 12th, 2010, 12:13	#11
Munaro Trader rating Join Date: Apr 2010 Location: Langley B.C	I solved my issue by changing the glass fuse out for a blade fuse, worked great. __________________ M4, L85, Mp5, Scar, Sig 552, M14

May 12th, 2010, 16:07	#14
CJay Trader rating Join Date: Oct 2008 Location: Belle River, ON	Fuse issue They're correct. Dc circuits will run fine under water provided the battery is not wet ad ur using sub 50V power supply. On the other hand I'd love to see an aeg on 120v haha. __________________ "Creator of the Zombat Sniper - oh yeah baby"

Fuse issue

Doctor's Corner