USR11 - Stock won't go back on.

youonlywish · April 7th, 2009, 20:56

Okay, first the mag wouldnt go in. I figured the hopup was too far forward, and the mag wouldnt fit in.

I took the stock off, took the hopup clamp (thing that screws into the top) off and realigned it.... now the stock wont go back in, after I've reattached the metal clamp...

I dont know... I ran into this problem before, but can't remember how I got it all back together.

Erennert · April 7th, 2009, 21:07

Hmm, Gun doctor?

Sorry, I'm not of much help, since i don't know anything about going into gearboxes, but i would guess theirs some sort of alignment problem where the stock attaches? I'm not sure, but It's my two cents.

Skladfin · April 7th, 2009, 21:24

put the rear side in first, and make sure the bottom of the trigger guard is in all the way.

Then push down the front side, you might use some force, but not too much.

youonlywish · April 7th, 2009, 21:46

I got it figured out.
Outer barrel was unscrewed only about a centimetre to the left..

I feel kinda dumb, but we all make mistakes.. it's all fixed up.

Cuddles · April 8th, 2009, 00:32

I used to have the same problem after I got my inner barrel upgrade. The inner barrel was getting pushed back causing the mag to not properly secure. I discovered that the end cap was putting a lot of pressure on the inner barrel (edgi barrels are made slightly longer than the stock barrel), which causes this misalignment. Didn't occur often, but it was an annoyance. I fixed it by putting an o-ring at the tip of the end cap, which gave it about 1-2mm of space and greatly reduced the pressure.

Don't know if this is a valid fix or not and not sure if anyone else has a similar problem, but it works well and does not affect the aesthetic appeal of the rifle.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

April 7th, 2009, 20:56	#1
youonlywish Trader rating Join Date: Mar 2006 Location: Brantford, ON.	USR11 - Stock won't go back on. Okay, first the mag wouldnt go in. I figured the hopup was too far forward, and the mag wouldnt fit in. I took the stock off, took the hopup clamp (thing that screws into the top) off and realigned it.... now the stock wont go back in, after I've reattached the metal clamp... I dont know... I ran into this problem before, but can't remember how I got it all back together. __________________ The Devil's Bench - Gaming Cafe, Brantford, ON.

April 7th, 2009, 21:46	#4
youonlywish Trader rating Join Date: Mar 2006 Location: Brantford, ON.	I got it figured out. Outer barrel was unscrewed only about a centimetre to the left.. I feel kinda dumb, but we all make mistakes.. it's all fixed up. __________________ The Devil's Bench - Gaming Cafe, Brantford, ON.

April 7th, 2009, 21:24	#3
Skladfin Trader rating Join Date: Dec 2006 Location: Glace Bay, Nova Scotia	put the rear side in first, and make sure the bottom of the trigger guard is in all the way. Then push down the front side, you might use some force, but not too much.

April 8th, 2009, 00:32	#5
Cuddles Trader rating Join Date: Oct 2008 Location: North Vancouver, BC	I used to have the same problem after I got my inner barrel upgrade. The inner barrel was getting pushed back causing the mag to not properly secure. I discovered that the end cap was putting a lot of pressure on the inner barrel (edgi barrels are made slightly longer than the stock barrel), which causes this misalignment. Didn't occur often, but it was an annoyance. I fixed it by putting an o-ring at the tip of the end cap, which gave it about 1-2mm of space and greatly reduced the pressure. Don't know if this is a valid fix or not and not sure if anyone else has a similar problem, but it works well and does not affect the aesthetic appeal of the rifle.

USR11 - Stock won't go back on.

Doctor's Corner