|
|
|
July 23rd, 2013, 18:54
|
#91 | |
|
will always be Mike Litoris in our hearts
|
Possibly, but it only does it with TM mags and not any other brand. KJW, KSC, and WE mags all fill perfectly.
__________________
Quote:
|
|
|
|
|
July 25th, 2013, 12:43
|
#92 |
|
GBB Whisperer
|
Does the magazine hiss after you've stopped filling?
|
|
|
|
|
July 25th, 2013, 14:25
|
#93 |
|
aka coachster
|
TM mags always piss (leak gas) while filling.
|
|
|
|
|
July 25th, 2013, 14:58
|
#94 | |
|
will always be Mike Litoris in our hearts
|
The mags do not leak or hiss after filling, but the valves like to spew gas while filling. It's not a huge plume of propane, but it's enough that the mags are only filled about 1/3 of its normal capacity. Any suggestions would be kindly appreciated. Thank you!
__________________
Quote:
|
|
|
|
|
|
July 25th, 2013, 15:27
|
#95 |
|
aka coachster
|
How long are you holding the tank on for? Try holding longer. They will leak/spew. It is normal for TM mags. You could consider new fill valves that have an oring on it or locate the tiny orings to add to the existing valves.
|
|
|
|
|
July 30th, 2013, 08:32
|
#96 |
|
previously Bunker_King
|
Thanks Coach for that helpful post. I used plumber silicon grease since my Canadian Tires never have what you need.
Western arms M1911 mags. |
|
|
|
|
November 4th, 2013, 12:47
|
#97 |
|
I did this on 4 KJW 1911 mags with great success.
Only difference is I did not fill any gas into it until it fully cured, as doing so would actually make a mess on the inside, if you are not over zealous with the gasket maker it will not ooze everywhere. I let it cure for 3 days, and I had none of the gasket maker come out from any mag after filling it and releasing the pin to test for debris. |
|
|
|
|
|
January 29th, 2016, 15:49
|
#98 |
|
Necro,
Did this few days ago on my leaky TM M&P9 mag as a last resort, let it cure for 24-48 hours. Worked brilliantly! Cheers. |
|
|
|
|
October 16th, 2018, 11:41
|
#99 |
|
I had poor luck lately fixing my mags and don’t have the patience anymore. Anyone good with fixing leaking mags from WA can PM me for the job ($).
I have 9 mags disassembled with more than 6 packs of brand new o-rings. Most of them leak from the outflow valve. |
|
|
|
|
June 29th, 2020, 20:16
|
#100 |
|
hey guys. found this thread via google.
I'm trying to seal 4x Tokyo Marui M9A1 mags. I took the bases off first, applied teflon tape, put the o-rings on, more teflon tape, lots of silicone oil on each step - still getting hissing / bubbling sound after filling the mags with propane. I filled the mags hours ago and I can still hear some of them hissing from the base from across the room. Only option left I can see is to use JB weld silicone - so do I strip the mag bases, clean with degreaser, apply the jb weld silicone sealant, put the o-ring on, put the jb weld silicone sealant on the inside of the mags too - insert the base into the mag, insert pins, put a bit of gas in, leave for 2 days to cure = fixed? Edit: will this stuff work? https://www.amazon.co.uk/gp/product/...FKNPWYKI&psc=1 Last edited by paradoxum; June 29th, 2020 at 20:20.. |
|
|
|
|
June 30th, 2020, 13:50
|
#101 | |
|
|
Quote:
https://www.amazon.co.uk/Permatex-80...omotive&sr=1-6 You need blue gasket maker, put it on like the guide and let it cure for 24-48 hours. |
|
|
|
|
|
June 30th, 2020, 14:29
|
#102 | |
|
|
Quote:
Will this work? I already got it on the way https://www.amazon.co.uk/gp/product/...?ie=UTF8&psc=1 |
|
|
|
|
|
June 30th, 2020, 15:32
|
#103 | |
|
|
Quote:
Blue was also able to remove in-case it decides to leak in a few years time. Best you can try it. |
|
|
|
|
|
June 30th, 2020, 16:07
|
#104 |
|
There was another guide on here where they recommended permatex black as a more permanent solution. I found that to be the case as well.
As long as it is a sealant that does not react to silicone oil and other propellants it should be fine. |
|
|
|
  |
|
||||||
| Bookmarks |
|
|
 |
|
