RS Type56-1 Feeding problem

security-101 · November 21st, 2010, 11:12

Hey guys, didn't know where to turn to for a problem like this so I thought you great people would be my answer............Ok so I went out and scooped a Type56-1 just this weekend and picked up a 8.4V 1500 battery for the rifle, I charged the battery for the three hours or so until my charger light turned green. I installed that I should have properly and fed some BB's into the 56 Mag and I found that none of the BB's were coming out, I would bang the Mag off my hand so that the BB's were at the top of the feeding lip. I then found that only 2 or 3 of the BB's were coming out, and then none would come out.........I took the Mag off and found that 4 or 5 BB's would drop out of the Mag hole in the bottom of the rifle................

I did alot of research on the RS Type56-1 before unloading my wallet! Can anyone give me some advice towards this problem..........Thanks

Amos · November 21st, 2010, 11:15

What BB's are you using?

The RS guns have very tight tolerances and wont feed some brands of BB.

You also need to put 2 drops of silicon oil in your magazine.

Kid · November 21st, 2010, 11:32

Just oil your mags and all shall be fine.

xaMdaM · November 21st, 2010, 22:02

Firstly, congrats on getting a really fine airsoft weapon. If you look after your pride and jpoy, it should give you years of good service.

Quote:

Originally Posted by security-101

....and fed some BB's into the 56 Mag and I found that none of the BB's were coming out, I would bang the Mag off my hand so that the BB's were at the top of the feeding lip. I then found that only 2 or 3 of the BB's were coming out, and then none would come out.........

Exactly how many BB's did you put in the magazine? "Just a few" might not be enough to properly feed the magazine. Often, at the end of its use, a magazine might still have some BB's in it but not enough to get sufficient spring tension in the winder. Make sure your mag is 1/2 full or more next time you test it.

I also agree with the other guys comments- sometimes the feed spring (inside the mag) sticks in places. A few drops of silicon oil keeps it moving freely. Just dont overdo it. "a little dab (or in our case, "drop") will do you.

Quote:

Originally Posted by security-101

.........I took the Mag off and found that 4 or 5 BB's would drop out of the Mag hole in the bottom of the rifle................

This is normal.

Kid · November 21st, 2010, 22:49

Off topic

I stripped the grub screw in the stock cap and it was halfway in, so I couldn't get the stock cap on my type 56-1. Couldn't get it out and just made the situation worse, so I decided to try to force it on with a clamp. I got it on with the clamp. Took it off and there was absolutely no damage done to the steel or the finish. The grub screw on the other hand was completely flattened (think railroad penny) against the inner side of the stock cap.

So yeah.... let that be a warning, don't strip the stock cap grub screw, and also, realsword steel is really nice. (I put the cap back on with superglue instead - seems like it will hold until I need it off)

FNG · November 22nd, 2010, 02:38

Quote:

Originally Posted by Amos

What BB's are you using?

The RS guns have very tight tolerances and wont feed some brands of BB.

You also need to put 2 drops of silicon oil in your magazine.

Can you elaborate on which brands?

Snakebite1967 · November 22nd, 2010, 05:31

also check the feed port a misaligned mag will cause the port to crimp which will stop bb feeding

Specs · November 22nd, 2010, 07:30

Quote:

Originally Posted by FNG

Can you elaborate on which brands?

It would be helpfull to know the brand...i have G&Ps and there have been problems

security-101 · February 4th, 2011, 08:15

Hey guys, thanks for all the help with my question I posted about the Type56-1, I found out that it was the bb's that were my problem. I had cheaped out on my bb's and bought them through Canadian Tire which I found out why I was getting them jammed. So I went out and pick me up some BB Bastard's bb's, and there way better!

Desmodus · February 4th, 2011, 08:24

Quote:

Originally Posted by security-101

Hey guys, thanks for all the help with my question I posted about the Type56-1, I found out that it was the bb's that were my problem. I had cheaped out on my bb's and bought them through Canadian Tire which I found out why I was getting them jammed. So I went out and pick me up some BB Bastard's bb's, and there way better!

OMG! NEVER use Canadian Tire BB's! Your poor gun! :P

Spike · February 4th, 2011, 08:47

Crappy Tire BBs in a RS? You just poured Colt 45 into the gas tank of your Lambo!

loafing_smurf · February 7th, 2011, 17:54

I was about the post the same problem for my Kalash/Cybergun AK-105. I loaded about 10 BBs that I got for free from another deal.

Sounds like I have to get my hands on a pack of good quality BBs to test fire my airsoft AK-105.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

November 21st, 2010, 11:12	#1
security-101 Trader rating Join Date: Nov 2010 Location: Guelph	RS Type56-1 Feeding problem Hey guys, didn't know where to turn to for a problem like this so I thought you great people would be my answer............Ok so I went out and scooped a Type56-1 just this weekend and picked up a 8.4V 1500 battery for the rifle, I charged the battery for the three hours or so until my charger light turned green. I installed that I should have properly and fed some BB's into the 56 Mag and I found that none of the BB's were coming out, I would bang the Mag off my hand so that the BB's were at the top of the feeding lip. I then found that only 2 or 3 of the BB's were coming out, and then none would come out.........I took the Mag off and found that 4 or 5 BB's would drop out of the Mag hole in the bottom of the rifle................ I did alot of research on the RS Type56-1 before unloading my wallet! Can anyone give me some advice towards this problem..........Thanks

November 21st, 2010, 11:15	#2
Amos Trader rating Join Date: Aug 2006 Location: Japan	What BB's are you using? The RS guns have very tight tolerances and wont feed some brands of BB. You also need to put 2 drops of silicon oil in your magazine. __________________ Custom Builds: FA3674U Krinkov G3SD6

February 4th, 2011, 08:47	#11
Spike Privateer Airsoft Trader rating Join Date: Dec 2008 Location: Beaverbank, NS	Crappy Tire BBs in a RS? You just poured Colt 45 into the gas tank of your Lambo! __________________ I change primaries like other people change socks.

November 21st, 2010, 11:32	#3
Kid Trader rating Join Date: Feb 2005 Location: Moose Jaw, SK	Just oil your mags and all shall be fine.

November 21st, 2010, 22:49	#5
Kid Trader rating Join Date: Feb 2005 Location: Moose Jaw, SK	Off topic I stripped the grub screw in the stock cap and it was halfway in, so I couldn't get the stock cap on my type 56-1. Couldn't get it out and just made the situation worse, so I decided to try to force it on with a clamp. I got it on with the clamp. Took it off and there was absolutely no damage done to the steel or the finish. The grub screw on the other hand was completely flattened (think railroad penny) against the inner side of the stock cap. So yeah.... let that be a warning, don't strip the stock cap grub screw, and also, realsword steel is really nice. (I put the cap back on with superglue instead - seems like it will hold until I need it off)

November 22nd, 2010, 05:31	#7
Snakebite1967 Trader rating Join Date: Jun 2006 Location: Tri cities canada	also check the feed port a misaligned mag will cause the port to crimp which will stop bb feeding

February 4th, 2011, 08:15	#9
security-101 Trader rating Join Date: Nov 2010 Location: Guelph	Hey guys, thanks for all the help with my question I posted about the Type56-1, I found out that it was the bb's that were my problem. I had cheaped out on my bb's and bought them through Canadian Tire which I found out why I was getting them jammed. So I went out and pick me up some BB Bastard's bb's, and there way better!

February 7th, 2011, 17:54	#12
loafing_smurf Trader rating Join Date: Oct 2010	I was about the post the same problem for my Kalash/Cybergun AK-105. I loaded about 10 BBs that I got for free from another deal. Sounds like I have to get my hands on a pack of good quality BBs to test fire my airsoft AK-105.

RS Type56-1 Feeding problem

Doctor's Corner