Noveske Metal body parts ID and outer barrel problems

oates76 · September 24th, 2012, 01:02

Hey guys, I'm installing a noveske metal body on to a friend's TM M16A2 and I'm a little stumped with some of the parts. It comes with a whole bunch of bags of little parts, no instructions or labels, and there are a few bits and pieces I'm lost on.

I'll post a photo, but just wondering if anyone could ID the parts. I believe some if not all should be in the fire selector switch, but take a look and let me know what you think.

Thanks in advance!

OAtes

I can't seen to get the picture to load in this thread, so here's the link. http://flic.kr/p/ddyZJK

L473ncy · September 24th, 2012, 01:09

The little ball bearing thing and spring is for the selector. Basically the ball and small spring fits against the reciever where the dimples in the selector area are. That's what gives you that "snap into place" thing.

As for the other pieces I have no clue but I'll see if I can dig up my Madbull receiver instructions to see if it will help.

EDIT: The other roll pin looks like it might be for your trigger guard, either that or it's for your bolt assist.

oates76 · September 24th, 2012, 14:23

Thanks for the reply. The other roller is stumping me too, it's too small for either. Oh well, it will become apparent at some point I think.

coach · September 24th, 2012, 14:58

roll pins are for the bolt assist or trigger guard

audi_bhoy · September 24th, 2012, 16:31

The remaining pin and spring is for the forward body pin, it prevents it from falling when removing it. Look on the right side of the lower body, just beside the pin hole there is a small hole, you insert the spring, the little pin, and then the body pin.

oates76 · September 25th, 2012, 00:33

Perfect Audi, thanks man. Knew it was something unusual

oates76 · September 30th, 2012, 22:55

Ok, stumped again. So I just about have the body alal together (changing over from a TM M16A2) and now I'm finding i cant mount the TM barrel assembly because the large TM outer barrel nut is a different size than the Noveske body. Aarrrrg.
Is this a well known problem with aftermarket metal bodies and original TM barrels?

Advice or tips. Do i just need to buy an aftermarket outer barrel system now too?

Thanks

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

September 24th, 2012, 01:02	#1
oates76 Trader rating Join Date: Mar 2005 Location: Calgary, AB	Noveske Metal body parts ID and outer barrel problems Hey guys, I'm installing a noveske metal body on to a friend's TM M16A2 and I'm a little stumped with some of the parts. It comes with a whole bunch of bags of little parts, no instructions or labels, and there are a few bits and pieces I'm lost on. I'll post a photo, but just wondering if anyone could ID the parts. I believe some if not all should be in the fire selector switch, but take a look and let me know what you think. Thanks in advance! OAtes I can't seen to get the picture to load in this thread, so here's the link. http://flic.kr/p/ddyZJK Last edited by oates76; September 30th, 2012 at 22:55.. Reason: Added pic

September 24th, 2012, 01:09	#2
L473ncy Trader rating Join Date: Oct 2004 Location: 11-30-24-1W5	The little ball bearing thing and spring is for the selector. Basically the ball and small spring fits against the reciever where the dimples in the selector area are. That's what gives you that "snap into place" thing. As for the other pieces I have no clue but I'll see if I can dig up my Madbull receiver instructions to see if it will help. EDIT: The other roll pin looks like it might be for your trigger guard, either that or it's for your bolt assist. __________________ ಠ_ಠLess QQ more Pew Pew READY TO >> RACE Last edited by L473ncy; September 24th, 2012 at 01:13..

September 24th, 2012, 14:23	#3
oates76 Trader rating Join Date: Mar 2005 Location: Calgary, AB	Thanks for the reply. The other roller is stumping me too, it's too small for either. Oh well, it will become apparent at some point I think.

September 24th, 2012, 14:58	#4
coach aka coachster Trader rating Join Date: Mar 2008 Location: T dot	roll pins are for the bolt assist or trigger guard

September 24th, 2012, 16:31	#5
audi_bhoy Trader rating Join Date: Mar 2009 Location: Trois-Rivières	The remaining pin and spring is for the forward body pin, it prevents it from falling when removing it. Look on the right side of the lower body, just beside the pin hole there is a small hole, you insert the spring, the little pin, and then the body pin.

September 25th, 2012, 00:33	#6
oates76 Trader rating Join Date: Mar 2005 Location: Calgary, AB	Perfect Audi, thanks man. Knew it was something unusual

September 30th, 2012, 22:55	#7
oates76 Trader rating Join Date: Mar 2005 Location: Calgary, AB	Ok, stumped again. So I just about have the body alal together (changing over from a TM M16A2) and now I'm finding i cant mount the TM barrel assembly because the large TM outer barrel nut is a different size than the Noveske body. Aarrrrg. Is this a well known problem with aftermarket metal bodies and original TM barrels? Advice or tips. Do i just need to buy an aftermarket outer barrel system now too? Thanks

Noveske Metal body parts ID and outer barrel problems

Upgrades & Modifications