Any Stanag Mag experts?

ronin49v · April 2nd, 2010, 16:14

Ok, here goes, I had a feeding issue with my G&P metal body and King Arms hop-up, the Mid-mags I had did not work with the new setup, even with black tape in the magwell and on the mags. I'm sure they will work if I put so much on that the mags don't move at all but it makes it difficult to remove.

the Mags I tried are:

Star
P-mag clones
King arms

none of these fed properly. HOWEVER, I tried these high cap mags that came with a TM M4A1 purchase, I was told were Tokyo Marui as well and they feed perfectly, no feeding issues whatsoever.

My Question is: How can you tell these are Tokyo Marui in case I want to buy more?
There is writing on the bottom plate of the mag, I expected it to say Tokyo Marui but it actually says (ADVENTURE LINE MFG CO INC. PARSONS KS USA)
Is this TM or something else?

Help?

Skladfin · April 2nd, 2010, 16:18

yup thats TM.

All the mags that you've tried more or less have been reported with longer feed lip retainer, you can cut it down by two millimetre or so, it should feed fine after.

ronin49v · April 2nd, 2010, 21:58

Thanks Skladfin

How should I cut it, from the front of the lip retainer towards the back or in an angle towards the back? That seems like a lot of plastic to take off. And will this ruin my mags for any other gun or hopup?

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

April 2nd, 2010, 16:14	#1
ronin49v Trader rating Join Date: Feb 2009 Location: Vancouver	Any Stanag Mag experts? Ok, here goes, I had a feeding issue with my G&P metal body and King Arms hop-up, the Mid-mags I had did not work with the new setup, even with black tape in the magwell and on the mags. I'm sure they will work if I put so much on that the mags don't move at all but it makes it difficult to remove. the Mags I tried are: Star P-mag clones King arms none of these fed properly. HOWEVER, I tried these high cap mags that came with a TM M4A1 purchase, I was told were Tokyo Marui as well and they feed perfectly, no feeding issues whatsoever. My Question is: How can you tell these are Tokyo Marui in case I want to buy more? There is writing on the bottom plate of the mag, I expected it to say Tokyo Marui but it actually says (ADVENTURE LINE MFG CO INC. PARSONS KS USA) Is this TM or something else? Help? Last edited by ronin49v; April 2nd, 2010 at 16:16..

April 2nd, 2010, 16:18	#2
Skladfin Trader rating Join Date: Dec 2006 Location: Glace Bay, Nova Scotia	yup thats TM. All the mags that you've tried more or less have been reported with longer feed lip retainer, you can cut it down by two millimetre or so, it should feed fine after.

April 2nd, 2010, 21:58	#3
ronin49v Trader rating Join Date: Feb 2009 Location: Vancouver	Thanks Skladfin How should I cut it, from the front of the lip retainer towards the back or in an angle towards the back? That seems like a lot of plastic to take off. And will this ruin my mags for any other gun or hopup?

Any Stanag Mag experts?

Accessories Discussion