|
|
|
March 2nd, 2013, 19:43
|
#76 |
|
"bb bukakke" KING!
|
that poor lonex motor.
__________________
I futz with V2s, V3s and V6s. I could be wrong... but probably, most likely not, as far as I know. |
|
|
|
March 2nd, 2013, 20:03
|
#77 |
|
I made a mess when I was 8, soldering for the first time, and no adult help.
Still not nearly as bad as that.
__________________
|
|
|
|
|
March 2nd, 2013, 20:22
|
#78 |
|
ya took a while to get hte solder out of the Spring coils but i did it and still works.. far as i know
 Not lonex, stock or the like. THANK GOD
__________________
A single Light is all one needs to find their way through the darkness, But a single BB is all you need to bring it on! ========== Im not worried about the Bullet that has my Name on it, Im worried about the bullet that says "to whom it may concern" Lt. Alexander Washington -(Red Tails 1944) Ret. Last edited by ScooterVauto; March 2nd, 2013 at 20:49.. |
|
|
|
|
March 2nd, 2013, 20:45
|
#79 |
|
I remember when I had my first M4 GBBR last year. I was trying to install my new Magpul trigger guard. Started punching out one of the pins out ... CLINK !
The lower body right underneath the trigger chipped off with the pin still in it. That's when I realised the pins were one-way pins. OH GOD WHY ...
__________________
West Coast EOD Supporter. // Bang One, Bang Em All ! // In war, it's not who's right, but who's left. |
|
|
|
|
March 2nd, 2013, 21:50
|
#80 | |
|
|
Quote:
__________________
|
|
|
|
|
|
March 2nd, 2013, 23:39
|
#81 | |
|
Quote:
|
|
|
|
|
|
March 3rd, 2013, 01:17
|
#82 | |
|
|
Quote:
heat the spring with soldering tool and tap pliers agianst hard surface. repeat.... till all the solders gone.. the motor was easier LOL
__________________
A single Light is all one needs to find their way through the darkness, But a single BB is all you need to bring it on! ========== Im not worried about the Bullet that has my Name on it, Im worried about the bullet that says "to whom it may concern" Lt. Alexander Washington -(Red Tails 1944) Ret. |
|
|
|
|
|
March 5th, 2013, 04:44
|
#83 |
|
|
ok this is a new one to me..
we have all seen various axle damage, but how about this note the "difference" in the axle Width  note the NUMBER of missing teeth  note the AMOUNT of material on the shell  Note the UNUSUAL shape of the bevel and spur gear lower bearings  note the LACK of the molded rings on the shell that is supposed to be around the spur and bevel gear bushings  Note the ONLY tooth i found in the box (its above the piston rails) and the factory seal was intact..  aperantly it was dry fired ALOT, but that much damage?? Discuss.
__________________
A single Light is all one needs to find their way through the darkness, But a single BB is all you need to bring it on! ========== Im not worried about the Bullet that has my Name on it, Im worried about the bullet that says "to whom it may concern" Lt. Alexander Washington -(Red Tails 1944) Ret. Last edited by ScooterVauto; March 5th, 2013 at 04:46.. |
|
|
|
|
March 5th, 2013, 05:26
|
#84 |
|
|
Are those grooved steel bushings?
__________________
|
|
|
|
|
March 5th, 2013, 05:37
|
#85 |
|
|
they look alot like modify dual oil channel bushings.
__________________
A single Light is all one needs to find their way through the darkness, But a single BB is all you need to bring it on! ========== Im not worried about the Bullet that has my Name on it, Im worried about the bullet that says "to whom it may concern" Lt. Alexander Washington -(Red Tails 1944) Ret. |
|
|
|
|
March 5th, 2013, 07:35
|
#86 |
|
That's caused by bad shimming and having to turning up the motor height to compensate for it. Basically the bevel gear sat too high and so the motor had to be turned all the way up to engage the teeth, but it also pushed the gear up and out of place. Over time like this, the side pressure not only chewed up the axle but elongated the bushings. That's why you can see that the elongated bushings is inline where the motor is going up. I always tell people that you need to check the shimming when a new motor is installed, as not every motor are the same dimension. Everyone needs to recheck their shimming every time you change the pistol grip or motor cage, motor, gears, bushings/bearings and gearbox shell.
__________________
Please email me as I'm not on ASC too often.  Custom Build | Upgrades | Repairs | Maintenance Contact: ghostgunwork@gmail.com / Private Message Last edited by HKGhost; March 5th, 2013 at 07:44.. |
|
|
|
|
March 8th, 2013, 12:06
|
#87 |
|
Mr. Silencer
|
M170 spring + Siegeteks + VFC Stock ARL
|
|
|
|
|
March 8th, 2013, 21:22
|
#88 | |
|
|
Quote:
so they are stock.
__________________
A single Light is all one needs to find their way through the darkness, But a single BB is all you need to bring it on! ========== Im not worried about the Bullet that has my Name on it, Im worried about the bullet that says "to whom it may concern" Lt. Alexander Washington -(Red Tails 1944) Ret. |
|
|
|
|
|
March 9th, 2013, 10:03
|
#89 |
|
"bb bukakke" KING!
|
dry firing does nothing.
__________________
I futz with V2s, V3s and V6s. I could be wrong... but probably, most likely not, as far as I know. |
|
|
|
|
March 10th, 2013, 14:23
|
#90 |
|
Fainting Goat, Dictator of Quinte West
|
rebar Thompson fix- bet it doesn't break there again
|
|
|
|
  |
|
||||||
| Bookmarks |
|
|
 |
|
