|
|
|
September 24th, 2015, 16:53
|
#16 |
|
When i push slide back, the Slide Stop does not locked the slide either...
Sent from my iPhone using Tapatalk |
|
|
|
September 24th, 2015, 17:00
|
#17 | |
|
Yes it spins. But I couldn't see much aventage. May be easier to insert into the lower receiver but I had hard time when it was new.
Quote:
__________________
aka Uncle 
|
|
|
|
|
|
September 24th, 2015, 17:03
|
#18 | |
|
|
Have you checked the metal piece inside the slide for reinfored slide stop use? Is there any loose?
Quote:
__________________
aka Uncle
|
|
|
|
|
|
September 24th, 2015, 17:36
|
#19 | |
|
|
Quote:
Im not sure which one that metal piece 😁 Sent from my iPhone using Tapatalk |
|
|
|
|
|
September 24th, 2015, 17:45
|
#20 |
|
|
Sent from my iPhone using Tapatalk |
|
|
|
|
September 25th, 2015, 08:13
|
#21 |
|
|
Added more info in post#3 to show how to fix the slide stop and trigger pull issues.
__________________
aka Uncle
|
|
|
|
|
September 28th, 2015, 11:02
|
#22 | |
|
|
https://m.facebook.com/airsoftDIYmod...&ref=bookmarks
Check it out, it may help. If you like diy, you could fix it yourself. Quote:
__________________
aka Uncle
|
|
|
|
|
|
October 15th, 2015, 08:30
|
#23 |
|
|
any ideas what is the best slide fit 5.1 gold match?
mine broken into half 
|
|
|
|
|
October 15th, 2015, 13:38
|
#24 | |
|
|
Wooh? ? What had happened? How would it be in half?
How many rounds you've put it through? Any of the 5.1 slides should fit in but just the front left mid frame rail will not have a good contact with other slides at the same spot since the Gold Match is a bit thicker with the reinforced metal piece. I have a Limcat metal slide and tried it on but never installed it, I have no idea at all for suggestions. Let the other experience hicapa user to give you advice. Quote:
__________________
aka Uncle
Last edited by N_Force; October 15th, 2015 at 13:44.. |
|
|
|
|
|
October 15th, 2015, 13:49
|
#25 |
|
|
Let me guess, the slide broke when you're firing, it cracked during blow back, and the back half of the slide went off track, right? Then you removed the slide and found it cracking and broke it?
What kind of gas you're using, propane? Green gas or 134a? I assume this point is the weakest for the design. Is the problem causing from green gas? May be?
__________________
aka Uncle
Last edited by N_Force; October 15th, 2015 at 13:52.. |
|
|
|
|
October 15th, 2015, 13:56
|
#26 |
|
|
This was what I posted on other thread:
The Japanese design is for 134 (75-80psi)but still able to handle propane(115psi). What you'll get is shorten the life use. When engage firing, gas is being releasing and flow through nozzle to push bb out from chamber and blow back the slide. The main impact are front and back horizontal, but don't miss out the vertical impact that creates between mag valve and nozzle. This impact also put pressure on the rails of slide and mid flame. That's how it got wear out faster and create problems, and that's how my 4.3 plastic slide got broken. Lubricant the contact could lengthen the life and minimize wear no matter is plastic or metal. After I learned and understand this situation and realized what would I expect the life of each. And that's also giving me a guide line to see if I would like to have it up grade or modify or not! __________________
__________________
aka Uncle
|
|
|
|
|
October 16th, 2015, 01:44
|
#27 | |
|
|
Quote:
the front come out with recoil spring . another hallf still inctact im using this gas  i think it green gas 134a |
|
|
|
|
|
October 16th, 2015, 01:49
|
#28 | |
|
|
Quote:
i belive i have been firing around 6000rounds  its cost me 2 unit output valve because the o-ring has been damage as well i'm using silicone spray to lubricant the parts inside.. i dont use grease at all. now i'm looking for this slide which i dont know if can fit it well or not http://shop.ehobbyasia.com/guarder-a...l#.ViCA034rLIU also asking my friend in japan to order the original slide for me if he can.. i dont know how to read and write in japanese as the order process required to fill in the form and sent the order through the form given in the box.. :banghead: Last edited by Sticksquad; October 16th, 2015 at 05:56.. Reason: fact |
|
|
|
|
|
October 16th, 2015, 11:25
|
#29 |
|
|
Thanks and good to know this slide can last for long even after you modified and fixed the slide stop. I thought it might not!
If the slide got broken when firing, I would think of we are using propane or green gas that the pressure is half the way high than 134a so it shorten the life time. But I never think of the slide would break in two pieces. I know the blow back on Glock, the pressure are on the outer barrel and the slide hitting the lower. And Gold Match design on the slide has slots in top front, I also feel like the material on GM is not as strong as regular hicapa so that could be reasons: 1, higher gas pressure. 2, weaker spots on those top of slide slots. Finally for this milage you put on this pistol, I'm happy for the result. But you are really love to shoot with this GM and put through a lot of rounds on it in a short period of time, lol! Thank for your information and I would like to know if you're able to order the new slide from Japan. Have you ever think about to get other new GM rather than just order the slide? BTW, what kind of Silicon spray you're using?
__________________
aka Uncle
Last edited by N_Force; October 16th, 2015 at 11:29.. |
|
|
|
|
October 17th, 2015, 06:44
|
#30 |
|
|
yes love to firing to release after works
 destroy all boxes in the house.its snappy feel better than my G18C. since not yet got any AEG in my hand. getting others GM in my country from local supplier would cost me another USD400 unless online shop can sent me parts by parts it would be easier to bypass the customs  then the cost would be cheaper than get it from local supplier. let me know if got people willing to ship parts  i try to get Age verification in here but seem not possible.. i'm using below silicone spray Last edited by Sticksquad; October 17th, 2015 at 07:07.. |
|
|
|
  |
|
||||||
| Bookmarks |
|
|
 |
|
