|
|
|
May 9th, 2008, 22:27
|
#16 |
|
*AV Status Suspended pending trade resolution*
|
   Needs an unobtrusive RDS, darker wood foregrips. in b4 'it's not 5.56, it's not 7.62, that rail's ugly'.
__________________
Age verifier- Halifax region |
|
|
|
May 10th, 2008, 03:49
|
#17 |
|
that is now a nice config, it may not be everybodies tast , I giong to do some bad things to people out there
 what make of Suppersor is that?
|
|
|
|
|
May 10th, 2008, 04:40
|
#18 | |
|
hmm i had thought that cyma aeg's were junk comparable to be's
you guys think this cyma ak is any good? http://cgi.ebay.com/New-AEG-AK47-CM0...QQcmdZViewItem how does it compare to the kraken ak? i got my kraken and was quite impressed with it but after a while it didnt seem as powerful anymore
__________________
 Quote:
|
|
|
|
|
|
May 10th, 2008, 09:40
|
#19 | |
|
*AV Status Suspended pending trade resolution*
|
Quote:
__________________
Age verifier- Halifax region |
|
|
|
|
|
May 10th, 2008, 11:00
|
#20 | |
|
Quote:
Bob, There's quite a few things I need to show you...  I can turn this east/west bastard of yours into a pile of pure pants creaming sex.
|
|
|
|
|
|
May 10th, 2008, 11:16
|
#21 | |
|
*AV Status Suspended pending trade resolution*
|
Quote:
I'm quite interested in hearing this.
__________________
Age verifier- Halifax region |
|
|
|
|
|
May 10th, 2008, 19:18
|
#22 | ||
|
|
Quote:
this is the part id need right?  it says its for TM since krakens are TM compatible
__________________
Quote:
|
||
|
|
|
|
May 10th, 2008, 21:02
|
#23 | |
|
|
Quote:
Yes, that part would work just fine, But take note, the kraken piston head requires a little bit of "destructive" work to get it off the piston. On the ones I've worked on I just dremel off the original piston head (it's a POS anyways) and install the new one. Instead of a G&P piston head, I'd suggest a modify or Systema... You get more bang for your buck with those brands. Oh. Stay far away from Area 1000 anything. |
|
|
|
|
|
May 10th, 2008, 22:03
|
#24 | |
|
|
do they sell those O rings by themselves? that sounds easier to replace
__________________
Quote:
|
|
|
|
|
|
May 10th, 2008, 23:43
|
#25 | |
|
|
Quote:
Just the right size is VERY difficult. (Keep in mind, to replace the Oring, you need to disassemble everything anyways, while you're at it you may aswell replace the piston head) Unless some one you know has upgraded their piston and everything and has a full TM stock piston (don't bother with stock CA pistons, many of them have the same problem as the cyma 028 pistons) upgrading piston head will be your best course of action. |
|
|
|
|
|
May 11th, 2008, 00:38
|
#26 | |
|
|
so then in that case it sounds like i should get this rather than the piston head itself
 im assuming that theyre not gun specific
__________________
Quote:
|
|
|
|
|
|
May 11th, 2008, 00:58
|
#27 | |
|
|
Quote:
but the back of stock marui heads have the string-grabber thingy... Buy that, take the head off, and take the spring to the hardware store and get yourself some thread locker and a proper sized nut to fit on the bolt. Really, you should just take the time and upgrade your piston head... everything you'll have to do is about the same amount of work.. and upgrading the piston head will give you the best result. |
|
|
|
|
|
May 11th, 2008, 01:04
|
#28 | |
|
|
ok thanks. ill think about it more before i buy something
heh. accidentally came accross an O ring for tm and ca on ebay after posting this. auction page says nothing about size 
__________________
Quote:
Last edited by Dusti69; May 11th, 2008 at 01:42.. |
|
|
|
|
|
May 11th, 2008, 02:11
|
#29 | |
|
|
Quote:
Just replace the whole piston head with something good. |
|
|
|
|
|
May 11th, 2008, 08:16
|
#30 |
|
Bob,
Do you think a very large 9.6V (1500mAh) stick battery would fit your AKS-74U without modifications?
__________________
|
|
|
|
  |
|
||||||
| Bookmarks |
|
|
 |
|
