FN SCAR Thread

[daishi]

Weeew, these rails are becoming a thing now. Also REVERSE magpul sticker, done with top coat nail polish







Sorry for the cell pics.

Big props go out to Siggypoo for cutting this rail to size and getting it ready to go. And for his impeccable choice in delivery box wrapping paper:


<3 U

[siggypoo]

Haha, thanks man. I hoped you'd get a laugh when I wrapped that, lol.
It looks great!


Location: YYZ VOR 062 radial, 17.5 DME

[BobbyDangerous]

Mine

[Short Round]

New Angrygun MREX Scar Rail.

Didn't really have any fitment issues surprisingly, other then some very minimal dremeling to fit it on my VFC Scar. Had to sand down two tabs that surround the gas block (took off like a quarter of a inch).

Not really sure if/when this will be released, I pre-ordered the rail when it had a release date of sometime in September, however I was told a copyright infringement had been handed out over this rail (I assume by Kinetic Development Group). Since then all sites that carry the rail have removed the product from their site or left the product page outdated, so I'm not sure if they still plan on releasing this.

[Desmodus]

Originally Posted by Short Round

New Angrygun MREX Scar Rail.

That is the hottest scar I've ever seen. I'm touching it next game.

[nstahl.19]

@short round did u engrave ur receiver? fckin beaut!

[Short Round]

Originally Posted by nstahl.19

@short round did u engrave ur receiver? fckin beaut!

Naw just vinyl carbon fiber stickers I made at my old job. It's the same stuff they use for car wraps.

[BioRage]

Very nice rail and setup, I will see this at LT's.

[pestobanana]

GOODBYE VFC SCAR



Externals:

-Laylax TangoDown Rail Extension
-MOE Style Grip (was advertised as PTS when I bought it, but it may not be)
-Madbull DNTC FSC G5 Flash Hider
-NCStar 1.1-4X25 P4 Illuminated Scope
-Larue SPR Scope Mount (clone)
-Magpul RSA QD (clone)

Drivetrain:

-VFC Mechbox Base
-BTC Spectre V2
-SHS High Torque Motor
-ZCI 13:1 Gear Set with 9 Tooth Bevel (more durable, but the ratio is closer to 15:1)
-VFC Sector Delayer
-Retro Arms Polyamide Piston
-Retro Arms Double O Ring Piston Head
-Lonex Cylinder Head with 3/16" Sorbo Pad and Neoprene Protector
-Lonex M4 Nozzle
-SHS Steel Full Cylinder
-SHS Tappet Plate
-Madbull M120 Spring (well worn in, so FPS is a bit lower)

-gears shimmed bevel-pinion
-gears and piston short stroked 2 teeth
-sorbo pad installed, AoE corrected
-gears lubricated with PTFE grease
-air seal assembly lubricated with silicone oil
-tappet plate modified for better air seal
-tappet spring cut for improved feeding
-BTC Spectre installed
-selector plate modified and shimmed
-trigger pull shortened
-Spectre re-wired for bullet connectors to maintain internal hinge wiring in stock
-Stock wiring re-wired using 16 AWG Primary Wire with Deans connector
-piston rack glued in for durability

Barrel Group:

-VFC SCAR Hop Up Unit
-VFC Hop Up Rubber
-R Hopped PDI 6.05 375mm Barrel

-R Hop patch installed to PDI barrel
-hop up arm modified, sorbo nub installed
-mound removed from rubber
-rubber greased and tied to barrel to prevent air leaks
-O ring added underneath adjuster to increase tension

[EOD Steve]

[BobbyDangerous]

[BobbyDangerous]

[Short Round]

I recently replaced my KDG Scar Rail with a RS Midwest Industries Scar Socom M-Lok Rail, as well as the Troy Scar Buffer Tube Adapter. It took A LOT of milling/dremeling to fit both parts on my VFC Scar (it is not RS Spec like VFC ARs, PTWs, etc.).





Was inspired by the gun below:

[Thenooblord]

[Desmodus]

^^^