Airsoft Canada
https://www.replicaairguns.ca/airsoft

Go Back   Airsoft Canada > Discussion > Doctor's Corner
Home Forums Register Gallery FAQ Calendar
Retailers Community News/Info International Retailers IRC Today's Posts

Turning off hopup in a KSC glock

:

Doctor's Corner

Reply
 
Thread Tools
Old June 18th, 2006, 00:13   #1
CuppoJava
 
Join Date: May 2006
Location: Calgary
Turning off hopup in a KSC glock

Hi,
My hopup, i discovered, is being extremely temperamental and inconsistent. So, as a last resort, I would like to turn it off. Does anyone know how to do this in a KSC glock?
So far, I've tried turning the hopup adjuster "gear" all the way clock-wise, which makes my BB's curve dramatically down! Now is this even possible? I thought the hopup rubber is located at the top of the barrel. What could possibly cause bb's to curve down?

Thanks for your help.
-Cuppo
CuppoJava is offline   Reply With Quote
Old June 18th, 2006, 10:42   #2
CDN_Stalker
Official ASC Bladesmith
 
CDN_Stalker's Avatar
 
Join Date: Jul 2003
Location: Ottawa, Ont.
Send a message via MSN to CDN_Stalker
At what range do the BBs curve down? 20ft? 100ft? If you didn't tamper with the hop up unit, using 0.25g BBs you should have it set about halfway. As for turning it off, because of the design, I don't think it's possible to fully turn it off.
CDN_Stalker is offline   Reply With Quote
Old June 18th, 2006, 16:23   #3
CuppoJava
 
Join Date: May 2006
Location: Calgary
The BB's are curving down at around 20 ft.
My "range" with hopup all the way off, is around 20 ft. Which means that I fire parallel to the ground from standing, and the bb hits the ground 20 ft out.
It's definately not gravity...

I dunno what's going on...

PS: I disassembled the hopup unit, and found the little bearing that pushes the hopup rubber down. Should I try removing this?
CuppoJava is offline   Reply With Quote
Old June 18th, 2006, 16:31   #4
CDN_Stalker
Official ASC Bladesmith
 
CDN_Stalker's Avatar
 
Join Date: Jul 2003
Location: Ottawa, Ont.
Send a message via MSN to CDN_Stalker
Let's start by asking how do you fill your mags with gas? If you fill right side up, then that'd explain your range. For the sake of braggin, I can get 0.30g BBs past 100ft and hit guys with it. Your's should do the same with heavier BBs. But lighter BBs will still go out to 50-60ft before going off wherever they choose to. Case in point, it's either something wrong with your gun (less likely) or something wrong with the way you gas up your mags.

Please explain in finer detail the way you do things with your G19, the way yo ufill it with gas, how long you've had it, if it was fine for a number of shots then it started screwing up, etc. Let's try to get operator error out of the equation, and see where we can properly focus our attention to best help you.
CDN_Stalker is offline   Reply With Quote
Old June 18th, 2006, 16:46   #5
CuppoJava
 
Join Date: May 2006
Location: Calgary
Thanks for all your help CDN_Stalker,
I'm pretty sure I gas up correctly. I'm using propane btw. I invert the mag and the propane tank and then fill.

I've had my glock 34 for about 2 months now, and the curving downwards thing started last week. I lube once every two weeks.

My friend owns an older gun that has no hopup, and it shoots as expected. The bb goes out as far as it can go and then gravity comes along and drags it to the ground.
So, because of the way the KSC hopup is designed, I won't be able to duplicate that behavior?
CuppoJava is offline   Reply With Quote
Old June 18th, 2006, 19:29   #6
CDN_Stalker
Official ASC Bladesmith
 
CDN_Stalker's Avatar
 
Join Date: Jul 2003
Location: Ottawa, Ont.
Send a message via MSN to CDN_Stalker
Any chance the hop up rubber got rotated? Slim shot but I can't think of anything else except filling the mag incorrectly (which it looks like you do properly).

You say you lube it, where exactly do you lube it? Sounds like maybe a slight chance that the striker that the hammer hits to extend it to release the gas isn't moving full forward, only giving you a tiny pop of gas instead of a full shot. If you have the slide off, drop some oil into the mechanism between the hammer and mag valve, and put yout thumb in front of the trigger to dampen it and cycle the action, pull trigger, push small vertical shaft that the slide hits to retract the striker, repeatedly to work the oil in. Sounds like a very odd case you have.

How many shots do you get out of a single gas fill? Generally a user will only get about two full mags through on a gas fill (keep in mind I'm using a KSC Glock 19, you might get more out of it, but shouldn't be much more). If you get 40-50 shots out of it, then I think maybe the mechansim isn't getting the full amount of gas released every shot (less gas released, less used in the gun). Of course, now that I think of it, not enough gas released, the slide won't cycle properly.

Ok, am confused now.
CDN_Stalker is offline   Reply With Quote
Old June 18th, 2006, 19:42   #7
CuppoJava
 
Join Date: May 2006
Location: Calgary
Hi CDN_Stalker,
I'm getting a little more than 2 mags on one fill. So I don't think it's the gas.

I think it's my hopup that's somehow broken.
When I turn it up all the way, then the bb arcs straight up.
But when I turn it down all the way, the bb's arcs straight down, behaving almost as if the hopup rubber was underneath the bb...

Anyway, the reason that I want to remove the hopup completely is because my gun is firing very inconsistently and inaccurately. Do you know of any tuning tips for getting the accuracy up?
CuppoJava is offline   Reply With Quote
Old June 18th, 2006, 20:21   #8
CDN_Stalker
Official ASC Bladesmith
 
CDN_Stalker's Avatar
 
Join Date: Jul 2003
Location: Ottawa, Ont.
Send a message via MSN to CDN_Stalker
When you turn it up, you are turning it counter clockwise? Sounds like you just need to tweak it more, very finely. If one way you get BBs going up and the other way down, doesn't sound like anything is wrong with it.
CDN_Stalker is offline   Reply With Quote
Old June 18th, 2006, 21:08   #9
CuppoJava
 
Join Date: May 2006
Location: Calgary
alright. I'll just try tweaking it more.
CuppoJava is offline   Reply With Quote
Old November 29th, 2006, 03:37   #10
tunabreath
 
tunabreath's Avatar
 
Join Date: Dec 2005
Location: Edmonton, AB
Sorry to bring this back, but it seems to belong and I'd rather not make a new thread.

My KSC Glock 18C is having a somewhat similar problem. When I crank the hopup all the way up(ccw), my shots arc upwards, and when I turn it all the way down(cw), my shots get sucked downwards, like antihop as previously described. I don't really mind this, since neither of those are exactly 'ideal' settings.

The problem is, in the middle, the first few shots (4-5) are dead on straight, but as I keep shooting, they start to sail upwards randomly, until all the remaining shots fly upwards. When I switch mags, same thing, first shots great, last shots horrendous.
Stalker, you mentioned that this may be a gas problem. Is the problem just that it's the middle of winter and my mags are cooling too fast as I shoot? I'm shooting pretty quickly without much of a break between shots.
Would lower velocity caused by lower pressure (cooldown+already cold to begin with) exaggerate the effects of hopup on same-weight BBs?
I haven't had any summer experience with my GBB yet (it's my first and I just recieved it recently), so I'm not really sure if this is to be expected during the cold season.
__________________
Vita, Passione e Pistole
tunabreath is offline   Reply With Quote
Old November 29th, 2006, 09:57   #11
CDN_Stalker
Official ASC Bladesmith
 
CDN_Stalker's Avatar
 
Join Date: Jul 2003
Location: Ottawa, Ont.
Send a message via MSN to CDN_Stalker
You'll really have to try it out in warmer weather, even +10C is too cold for GBBs (is fine for my gas M700 if the mags are kept in pocket). Other thing is to increase the weight of your BBs, I've found that even 0.25g are too light for most use (but work if in a tightspot, like having to reload out of your AEG mags). Heavier BBs are more stable and give a more consistant trajectory.
CDN_Stalker is offline   Reply With Quote
Old November 29th, 2006, 10:24   #12
Tankdude
 
Join Date: Jan 2005
Location: East Coast, New Brunswick
Quote:
Originally Posted by CuppoJava View Post
So far, I've tried turning the hopup adjuster "gear" all the way clock-wise, which makes my BB's curve dramatically down! Now is this even possible?
It is called gravity.
Tankdude is offline   Reply With Quote
ReplyTop


Go Back   Airsoft Canada > Discussion > Doctor's Corner

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Airsoft Canada
https://www.replicaairguns.ca/airsoft

All times are GMT -4. The time now is 18:18.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.