G36C Woes

Trader rating · October 27th, 2008, 02:35

I tried to get prowin hop up working in my G36 with no luck. Had better performance from JG hop up (just sad)

Spa · October 27th, 2008, 03:25

tommrow when i have time ill show up what a modded prowin g36 hop up looks like

im lazy right now

Spa · October 27th, 2008, 14:48

So as you can tell, for some gearboxes the hop up does require modification, but overall works great in my g36!

bunta510 · January 12th, 2009, 21:25

nice tip spa. On my part, what i did was replace the original screw on the front end of the gearbox with a grub screw from one of my suppressors. although after installing the prowin Hop up, i lost around 50 fps on my CA SL8-2. i think CA uses a different size/dimensions of air seal nozzle compared to TM/JG?

Spa · January 12th, 2009, 21:43

i use a Prometheus G36C air seal nozzle. And yes, TM and CA use different Nozzles in thier G36 series. The difference is that the TM one is just a simple nozzle but the CA has a rail, and has a T bar at the end that connects to the tappet plate so it does not roll (this is so the rail can glide in the chamber).

bunta510 · January 13th, 2009, 01:22

aside from the rail, are they of the same length? would a nozzle with rail be better compared to one that has none?

Spa · January 13th, 2009, 13:40

The rail is special for the CA hopup units and are not necessary for TM hop up units. The Prometheus nozzle for the CA is the same size as a TM one.

If you wanted to shave off the rail on the CA one to make it compatible with a TM im sure it can be done.

Fireboy · April 16th, 2009, 02:49

So my solution was simple with the Star G36...
Split the gun...very carefully.
Completely remove the outer barrel assembly and magwell. Once removed if you look at the front portion of the main body where the magwell attaches there is a small screw there. Remove it and save it, once removed you can pull that portion of the G36 body apart...at least on a Star one you can. I slid the complete hop up with inner barrel attached into the main receiver, pulled and locked the charging handle back and finally screwed the hopup onto the mechbox through the ejection port. Now, here's the unfun part. You have to mod your outer barrel. I cut the portion that used to hold the old hop up in place in half so the inner barrel would just pop right in. Keep in mind that the hopup is now held in place by the mechbox...as was meant to by ProWin. Now she runs perfectly. I'm loving it.
And spring changes are a piece of cake...it's a Star so I fold the stock over, grab an allen key and pop out the old spring and put in a new one.

I'll post pics in the next day or two.

Cheers

tanman · March 29th, 2010, 23:09

For those who care, the thread in the hop up for connecting to your mechbox is metric, M3 x .50 . You can get it at Fastenal, if there is one around you, or maybe a hardware store. It will also pass through the threading on the mechbox without damage. I'm planning on putting this on my Echo1 G36, not fully done yet, will post results later.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

January 12th, 2009, 21:25	#34
bunta510 Trader rating Join Date: Sep 2008	nice tip spa. On my part, what i did was replace the original screw on the front end of the gearbox with a grub screw from one of my suppressors. although after installing the prowin Hop up, i lost around 50 fps on my CA SL8-2. i think CA uses a different size/dimensions of air seal nozzle compared to TM/JG? Last edited by bunta510; January 12th, 2009 at 22:11..

January 12th, 2009, 21:43	#35
Spa Trader rating Join Date: Oct 2006 Location: Winnipeg, Manitoba	i use a Prometheus G36C air seal nozzle. And yes, TM and CA use different Nozzles in thier G36 series. The difference is that the TM one is just a simple nozzle but the CA has a rail, and has a T bar at the end that connects to the tappet plate so it does not roll (this is so the rail can glide in the chamber). Last edited by Spa; January 12th, 2009 at 21:46..

October 27th, 2008, 02:35	#31
scooby Guest Trader rating	I tried to get prowin hop up working in my G36 with no luck. Had better performance from JG hop up (just sad)

October 27th, 2008, 03:25	#32
Spa Trader rating Join Date: Oct 2006 Location: Winnipeg, Manitoba	tommrow when i have time ill show up what a modded prowin g36 hop up looks like im lazy right now

January 13th, 2009, 01:22	#36
bunta510 Trader rating Join Date: Sep 2008	aside from the rail, are they of the same length? would a nozzle with rail be better compared to one that has none?

January 13th, 2009, 13:40	#37
Spa Trader rating Join Date: Oct 2006 Location: Winnipeg, Manitoba	The rail is special for the CA hopup units and are not necessary for TM hop up units. The Prometheus nozzle for the CA is the same size as a TM one. If you wanted to shave off the rail on the CA one to make it compatible with a TM im sure it can be done.

April 16th, 2009, 02:49	#38
Fireboy Trader rating Join Date: Dec 2006 Location: Alberta, Earth	So my solution was simple with the Star G36... Split the gun...very carefully. Completely remove the outer barrel assembly and magwell. Once removed if you look at the front portion of the main body where the magwell attaches there is a small screw there. Remove it and save it, once removed you can pull that portion of the G36 body apart...at least on a Star one you can. I slid the complete hop up with inner barrel attached into the main receiver, pulled and locked the charging handle back and finally screwed the hopup onto the mechbox through the ejection port. Now, here's the unfun part. You have to mod your outer barrel. I cut the portion that used to hold the old hop up in place in half so the inner barrel would just pop right in. Keep in mind that the hopup is now held in place by the mechbox...as was meant to by ProWin. Now she runs perfectly. I'm loving it. And spring changes are a piece of cake...it's a Star so I fold the stock over, grab an allen key and pop out the old spring and put in a new one. I'll post pics in the next day or two. Cheers

March 29th, 2010, 23:09	#39
tanman Trader rating Join Date: Mar 2010	For those who care, the thread in the hop up for connecting to your mechbox is metric, M3 x .50 . You can get it at Fastenal, if there is one around you, or maybe a hardware store. It will also pass through the threading on the mechbox without damage. I'm planning on putting this on my Echo1 G36, not fully done yet, will post results later.

G36C Woes

Doctor's Corner