|
|
|
|
|
||||||||
|
|
|||||||||
| Home | Forums | Register | Gallery | FAQ | Calendar |
| Retailers | Community | News/Info | International Retailers | IRC | Today's Posts |
 |
|
|
Thread Tools |
October 30th, 2005, 23:46
|
#1 | |
|
Leaking GBB Mags
Alright, I have WA Beretta 92fs and whenever I fill up the mags there all fine and dandy, no leaking, no hissing noises.....no nothing. But, as soon as I put either of the two mags into the gun, baam, they start to leak instantly and at a pretty high rate. Does anyone have any ideas on how to fix this problem, or is it a problem with the gun?
Note: one of the mags previously leaked, but I got some new seals for it and it was working fine for about a week, then this problem started to occur. Thanks.
__________________
I C U "Loser's do There Best. Winner's go home and Fuck the Prom Queen!" Quote:
|
|
|
|
|
October 30th, 2005, 23:58
|
#2 |
|
WW2 Airsofter
|
What kind of gas are you using? As well, are you putting silicone oil in your mag's before you gas them up?
Erik
__________________
I can't measure my sig so I got this stupid tag line instead. |
|
|
|
|
October 31st, 2005, 00:11
|
#3 | |
|
|
Regular WA mags (didn't think/know I could use other brands...), and yes, I use silicone oil before I gas them up....by the way I am using Green Gas with them.
__________________
I C U "Loser's do There Best. Winner's go home and Fuck the Prom Queen!" Quote:
|
|
|
|
|
|
October 31st, 2005, 00:15
|
#4 |
|
Don't use green gas, use propane... but don't use either in this gun, you need to use duster/134, green/propane will kill your WA, they are not meant for that, that is likely the problem, too much pressure
|
|
|
|
|
|
October 31st, 2005, 00:16
|
#5 | |
|
|
Awsome....should I replace the seals on the mags again? seeing how I have been using GG on her for the past 3 or so months?
__________________
I C U "Loser's do There Best. Winner's go home and Fuck the Prom Queen!" Quote:
|
|
|
|
|
|
October 31st, 2005, 00:19
|
#6 |
|
Stop using Green now, get some duster and a duster adapter (pm Madmax), if it does not leak, then your seals are ok, if they do, replace them and use duster, no more problems, but whatever you do... don't use GG in a WA.
|
|
|
|
|
|
October 31st, 2005, 00:24
|
#7 | |
|
|
Alright, thanks man
__________________
I C U "Loser's do There Best. Winner's go home and Fuck the Prom Queen!" Quote:
|
|
|
|
|
|
November 2nd, 2005, 14:58
|
#8 | |
|
i dont know why everyone says dont use green gas in WA,
ive been using green gas in my SVI for a long time and no probs yet but maybe im just lucky
__________________
Pantless_Crab Wrote: Quote:
|
|
|
|
|
|
November 2nd, 2005, 15:55
|
#9 |
|
Myoga
|
The seals and valves on WA mags only need to withstand the vapour pressure of HFC-134a for their purposes. If it can withstand propane, then it was over-engineered.
|
|
|
|
|
November 2nd, 2005, 16:06
|
#10 |
|
Official ASC Bladesmith
|
Need to oil the linkage that presses the release valve on the mag when the hammer hits it. The link pivots on an axle and if that becomes sticky (not enough oil) then it'll hit the release vavle and not return the way it should, therefore holding the vavle open and you lose all your gas.
|
|
|
|
 |
|
||||||
| Bookmarks |
| Thread Tools | |
|
|
 |
|
