JB Weld source?

Kokanee · May 28th, 2005, 14:53

Anyone know where I could find jb weld? Checked both rona and home despot and a no go on both.

cheers

concept_8 · May 28th, 2005, 15:13

try crappy tire bud, that's where I always get it.

Mantelope · May 28th, 2005, 15:23

I get it at CP. They can probably order it in for you if they don't stock it. JB Weld is definitely the best epoxy I've ever used, it's holding my broken metal body together. the JB Kwik stuff isn't nearly as strong though... it's about as strong as regular epoxy, but dries in four minutes. Like, it's actually solid after four minutes, unlike regular "five minute" epoxy.

MadMax · May 28th, 2005, 15:25

I've found a trick which works better than JB weld for larger structural fillet repair. I've found that a big slug of JB is pretty strong under compression, but under tension, I find it to be too brittle and crack prone. It seems that it's stiff, but it propagates cracks.

If you want to make a big gross joint, try wadding steel wool into the area. Heavily saturate the steel wool with good 2hr epoxy (5min is less tough). You can put on gloves and saturate the wool before smooshing it into place. After a couple days cure, you get a slug of steel wool in epoxy matrix which is very strong. I've socked a hunk of the stuff with a mini sledge and only the edges which aren't held in with steel break off.

It's pretty hard to break the major body of goo apart with the steel wool pulling it together. You want the steel wool to be smushed together as tight as you can. More total steel cross section means more steel pulling the epoxy together. All the epoxy does is bond at the outer surfaces and keep the wool from shifting. For even more strength, use stainless steel steel wool. It's available in Can Tire.

Kokanee · May 28th, 2005, 16:10

i'm repairing my ics lower m4 reciever until i can get a new one. It snapped in half just behind the rear body pin. Amazingly, the upper reciever tabs are completely intact and holding the body together still....

i'm not expecting to be able to mount my sliding stock back on it, but just want to throw the broken part of the reciever back on to protect the innards from the elements.

Bigmatty · May 28th, 2005, 16:32

canadian tire..automotive section

ert · May 29th, 2005, 18:15

I get all mine for free from work

I have a few boxes of the stuff at home...

We get it when we buy certain tek connectors for big electrical cables at work. It's used to make the connector explosion proof and on sites where explosion proofing is not specced in the contract, we get tons of the stuff.

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

May 28th, 2005, 14:53	#1
Kokanee Ministry of Peace Trader rating Join Date: Mar 2002	JB Weld source? Anyone know where I could find jb weld? Checked both rona and home despot and a no go on both. cheers

May 28th, 2005, 15:13	#2
concept_8 Trader rating Join Date: Sep 2004 Location: sudbury Ont.	try crappy tire bud, that's where I always get it. __________________ "Death in the tall grass"

May 28th, 2005, 15:23	#3
Mantelope Scotty aka harleyb Trader rating Join Date: Mar 2004 Location: Toronto, Ontario	I get it at CP. They can probably order it in for you if they don't stock it. JB Weld is definitely the best epoxy I've ever used, it's holding my broken metal body together. the JB Kwik stuff isn't nearly as strong though... it's about as strong as regular epoxy, but dries in four minutes. Like, it's actually solid after four minutes, unlike regular "five minute" epoxy. __________________

May 28th, 2005, 15:25	#4
MadMax Delierious Designer of Dastardly Detonations Trader rating Join Date: Dec 2001 Location: in the dark recesses of some metal chip filled machine shop	I've found a trick which works better than JB weld for larger structural fillet repair. I've found that a big slug of JB is pretty strong under compression, but under tension, I find it to be too brittle and crack prone. It seems that it's stiff, but it propagates cracks. If you want to make a big gross joint, try wadding steel wool into the area. Heavily saturate the steel wool with good 2hr epoxy (5min is less tough). You can put on gloves and saturate the wool before smooshing it into place. After a couple days cure, you get a slug of steel wool in epoxy matrix which is very strong. I've socked a hunk of the stuff with a mini sledge and only the edges which aren't held in with steel break off. It's pretty hard to break the major body of goo apart with the steel wool pulling it together. You want the steel wool to be smushed together as tight as you can. More total steel cross section means more steel pulling the epoxy together. All the epoxy does is bond at the outer surfaces and keep the wool from shifting. For even more strength, use stainless steel steel wool. It's available in Can Tire. __________________ Want nearly free GBB gas?

May 28th, 2005, 16:10	#5
Kokanee Ministry of Peace Trader rating Join Date: Mar 2002	i'm repairing my ics lower m4 reciever until i can get a new one. It snapped in half just behind the rear body pin. Amazingly, the upper reciever tabs are completely intact and holding the body together still.... i'm not expecting to be able to mount my sliding stock back on it, but just want to throw the broken part of the reciever back on to protect the innards from the elements.

May 28th, 2005, 16:32	#6
Bigmatty Super Moderator Trader rating Join Date: Apr 2002 Location: Victoria BC	canadian tire..automotive section __________________ Bigmatty Bad Karma (Pacific) BCAC BUY/SELL RATING

May 29th, 2005, 18:15	#7
ert Trader rating Join Date: Jul 2003	I get all mine for free from work I have a few boxes of the stuff at home... We get it when we buy certain tek connectors for big electrical cables at work. It's used to make the connector explosion proof and on sites where explosion proofing is not specced in the contract, we get tons of the stuff. __________________ E Nomini Patri, E Fili, E Spiritu Sancti My Old ASC Buy/Sell Rating

JB Weld source?

Doctor's Corner