Airsoft Canada > Search Forums Search Results			User Name Remember Me? Password

Showing results 1 to 10 of 10 Search took 0.02 seconds. Search: Posts Made By: Tuthmose

Forum: Doctor's Corner February 13th, 2010, 23:21

Replies: 2 Fitting new slide and outer barrel/chamber Views: 4,765 Posted By Tuthmose Thanks, Rock and Roll Outlaw. I'm thinking the... Thanks, Rock and Roll Outlaw. I'm thinking the outer chamber is the way to go as well, but would feel better about it if one of the GBB pros (Illusion, RacingManiac, looking at you here . . .)...

Forum: Doctor's Corner February 13th, 2010, 21:59

Replies: 2 Fitting new slide and outer barrel/chamber Views: 4,765 Posted By Tuthmose Fitting new slide and outer barrel/chamber Hey all, In the process of fitting and tuning my ProG4 slide and T-K one-piece outer barrel/chamber set, I've run into an issue I'd like some experienced advice with. The gun works: it fires...

Forum: Gear Discussion January 21st, 2010, 09:58

Replies: 0 Holster for 4.3 with tac-light? Views: 3,121 Posted By Tuthmose Holster for 4.3 with tac-light? My apologies up front if this is a repeat of a previously-asked question, but I couldn’t find an answer in my searches here. I’m looking to find a Blackhawk Serpa or Safariland holster for a...

Forum: Newbie Tank January 8th, 2010, 18:03

Replies: 11 Soldering to Deans connectors Views: 8,505 Posted By Tuthmose Hmm. Ok, questions: Frankly, if your... Hmm. Ok, questions: Frankly, if your battery tests ok, I wouldn't worry to much about the possible spark you saw. Not much you can do about it now anyway. You say your battery tests fine. ...

Forum: Doctor's Corner January 8th, 2010, 16:53

Replies: 79 Hi-Capa 4.3 : Creation Outer Barrel Compatibility with PGC slide Views: 63,366 Posted By Tuthmose Thank you, ILLusion - I appreciate your sharing... Thank you, ILLusion - I appreciate your sharing your knowledge! -Tuthmose

Forum: Newbie Tank January 8th, 2010, 16:29

Replies: 11 Soldering to Deans connectors Views: 8,505 Posted By Tuthmose As obvious as this may seem, I'll throw it out... As obvious as this may seem, I'll throw it out there anyway in the spirit of "better safe that sorry": When changing over the battery's connector, be sure to do one wire at a time, completing it...

Forum: Doctor's Corner January 8th, 2010, 13:17

Replies: 79 Hi-Capa 4.3 : Creation Outer Barrel Compatibility with PGC slide Views: 63,366 Posted By Tuthmose LOL - ok, point taken. What I should have said... LOL - ok, point taken. What I should have said was "so I don't frag things too quickly . . ." :) Ahhhh. [*mental lightbulb goes one*] The new-style barrels are fixed? Are they anything...

Forum: Doctor's Corner January 7th, 2010, 20:17

Replies: 79 Hi-Capa 4.3 : Creation Outer Barrel Compatibility with PGC slide Views: 63,366 Posted By Tuthmose Thank you both very much, gentlemen! I shall now... Thank you both very much, gentlemen! I shall now commence assemblin' and tunin' . . . I'm also assuming that, since the T-K chamber is aluminum, the danger of impact damage is minimized anyway? ...

Forum: Doctor's Corner January 7th, 2010, 12:08

Replies: 79 Hi-Capa 4.3 : Creation Outer Barrel Compatibility with PGC slide Views: 63,366 Posted By Tuthmose My apologies ahead of time for what is the mother... My apologies ahead of time for what is the mother of all necro-posts, but my question was heavily tied to this thread's topic . . . Are the newer (as in, I got one two weeks ago) ProG4 slides...

Forum: Newbie Tank January 7th, 2010, 11:53

Replies: 1,632 Sticky: Introduction Thread: Post your hello's here not somewhere else. Views: 4,803,740 Posted By Tuthmose Greetings everybody! I've used your fine... Greetings everybody! I've used your fine site for information and resources for quite some time, but recently had the need to post a question, so I figured it was a good a time as any to pop over...

Showing results 1 to 10 of 10