Airsoft Canada - mp5 maxed out parts

Airsoft Canada (https://airsoftcanada.com/forums.php)

- Upgrades & Modifications (https://airsoftcanada.com/forumdisplay.php?f=24)

- - mp5 maxed out parts (https://airsoftcanada.com/showthread.php?t=53522)

mp5 maxed out parts

Hi guys.
I was wondering out of these parts what you guys would suggest. I am going to be getting a combination of parts and was wondering what you guys would pick.

So far i have ALREADY INSTALLED

systema m120

systema magnum motor

king arms 8mm gearbox

prometheous high speed gears

systema type O cylinder

madbull 6.03 inner barrel (AK length)

madbull shark accelerator hopup ( horrible, going to be replacing it with guarder)

king arms long silencer

2-6X30 scope

9.6 3600 MAH

I would like to get some new parts:

Please pick the best setup that works well together, including with my already installed parts.

For pistons:

guarder V2 piston
supercore piston
Prometheus piston
Angel piston

For Cylinder heads:

Guarder Cylinder head V2
Prometheus cylinder headv2

Piston Heads:
G&P explosive piston head
Systema duracon bearing piston head

I will be purchasing a firefly hard bucking and big out H nub.

Thanks a lot guys

Quote:

Originally Posted by babacanoosh (Post 653852)

Hi guys.
I was wondering out of these parts what you guys would suggest. I am going to be getting a combination of parts and was wondering what you guys would pick.

So far i have:

systema m120 - Too high, will put you well over 400fps. Two weeks ago I put a Prometheus 120 spring in my MP5SD and it settled down to 430fps with hop up ON!!!!

systema magnum motor - If you want, I prefer EG700, no experience with Systema motors though, don't see the point.

king arms 8mm gearbox - King Arms 6mm mechbox, better without the problem with bearings, they jam up on the gears and fall apart sometimes.

prometheous high speed gears - High speed gears are meant for springs that shoot under 330fps, best used with stock springs actually

systema type O cylinder - Reason?

madbull 6.03 inner barrel (AK length) - Sure, good barrels

madbull shark accelerator hopup ( horrible, going to be replacing it with guarder) - Madbull 60deg rubber is serving me well now, is in three of my guns (MP5SD shooting 400fps, MP5A with PDW stock shooting 330fps, CA M24 shooting 500fps)

king arms long silencer

2-6X30 scope - Too much for an MP5, get a low profile mount and an RDS of some type.

9.6 3600 MAH - Good if you are running a 400fps spring (or more), overkill if anything under 400fps. That combined with hi-speed gears will shred pistons at the extreme rate of one piston every game or two (if you make it that long, a client went through two Systema Red pistons in two weeks with the same set up)

I would like to get some new parts:

Please pick the best setup that works well together, including with my already installed parts.

For pistons:

guarder V2 piston
supercore piston
Prometheus piston
Angel piston

For Cylinder heads:

Guarder Cylinder head V2
Prometheus cylinder headv2

Piston Heads:
G&P explosive piston head
Systema duracon bearing piston head

I will be purchasing a firefly hard bucking and big out H nub.

Thanks a lot guys

Offered my opinions.

If you're getting an Ak length inner barrel, you only need a Systema Type-1 cylinder for a perfect fit. Type-0 is a bit too big, but could still work. Type-1 is a better fit, though.

I 2nd Cdn_Stalker's opinion on the battery being too excessive.

Buy a complete systema gearbox with motor, screw messing around with parts not designed and factory QC'd to fit and work together perfectly.
It will be better and save you money more than likely.

Quote:

Originally Posted by Naglfar (Post 653901)

Buy a complete systema gearbox with motor, screw messing around with parts not designed and factory QC'd to fit and work together perfectly.
It will be better and save you money more than likely.

+1 go for the drop in mechbox save you time and money, also easy on the technically challenged.

um, i would rather not with the drop in, maybe on my next gun, but the price for the mechbox would have saved money in the beginning...but at this point,i dont think so. Even if i sold all of these parts, i would probably end up paying another $150...also I am not technically challenged, im ok with putting parts in and shimming. And to clear these things up, i have all of the parts installed already, im just wondering about the parts that i listed to choose from. Also, Illusion, im a bit confused with the cylinder. I have been told by countless sources to get a type o cylinder for my length barrel....I had a hurricane type A cylinder in before, but that didnt cut it at all. I am now using the type o, and am getting 400 fps (instead of 390 as before) pretty consistently with an m120 spring. So im a bit confused about a type 1...as for my old setup though as stalker comented on...it has held up for 4-5 months of pretty heavy use, and shows barely any sign of wear....

Systema lists the type-1 SPECIFICALLY as an AK-47 length cylinder.

http://www.wgcshop.com/pcart/shopper...m=SYS-ZS-04-17

Most people actually aren't aware of its existance, because most manufacturers don't create that intermediary cylinder between the Type-0 (full length) and Type-2 (1/4 ported), which are the two most commonly used sizes.