A+ Devil 370mm Inner barrel for KSC/KWA MP7A1
 

So I finally found the Falcon 6.03mm 363mm inner barrel for KWA MP7, but the place wanted $30 USD to ship it.

Sooo, I found the A+ Devil 370mm Inner barrel for the KSC MP7

Anybody have experience with this? The bore is 6.01mm...

http://www.brotherprice.com/ebphoto/...0KSC%20Mp7.jpg

I've been curious about this as well. Considering how hard it is to find an in-stock Falcon one. Downside to me was that with 6.01mm I'm worried that it will jam a lot.

Where did you see this barrel?

Which the Falcon or the A+?

Falcon's on Kic.com.tw
A+ is on EBAirsoft

A+

Interesting... I've been looking for a longer barrel. Was even considering the Angry Gun silencer route, but I've never been a fan of barrel extension silencers...

I was borderline considering getting a custom barrel made.

I did some research and found out that the Angry Gun suppressor increases FPS but is horrible for accuracy. Users reported wildly-varying trajectories.

The accuracy issue was my main concern, as it was always an issue with such designs. Thanks for that heads up. I'll keep my eyes open for the A+ barrel appearing through my normal channels.

Here's the point form notes from what I've seen of the AngryGun/A+ stuff.

- well built and consistently made
- fit to original parts is very good...good tolerances
- on a KWA MP7 the FPS with a A+ hopup rubber (very nice) was 400fps w/ 0.2's...350fps w/0.30's. With the AG Suppressor (6.01 tighbore extension) it clocked 500fps w/0.20's and 450fps w/0.30's. Crazy hard shots.
- on the AG suppressor there was a good ring of BB impact as the BB transitioned from the stock inner to the 6.01 tightbore. Obviously the BB's were impacting right at the seam...didn't really see any rub marks further down
- stock accuracy was very good. Certainly adequate for 30-40ft CQB. Accuracy with the AG suppressor was not as good. Fine for sub 40ft CQB (or whatever it is kitty corner across TTAC). You could hit poppers with sufficient regularity off hand.
- I suspect that the length of the AG suppressor is enough to mostly restabilize the BB after the transition...but the fliers might be due to nicks/damage to the BB from the transition.
- no jams...but it's a very tight bore

All in all, their stuff is good. I like how the suppressor pushes up to the inner...but the way it mates and the fact that it's off size is no good.

In lieu of any actual experience with the A+ inner barrel . . .
I went and bought the A+ rubber, A+ barrel and some knockoff MP7 suppressor.


I shall report back in a few weeks (when it shows up at my door)

I look forward to your report.

I got a bunch of these A+ hop up rubbers for all gun platforms as well, since they've been getting rave reviews internationally. I haven't had a chance to test them yet, but the quality of them is fantastic. I can't wait to give these a go...

Yeah I've been using the A+/REAPS buckings for a bit now and they're pretty solid. Only thing is that there's a wear-in period on them (at least the ME2s anyway). About on-par or a bit better than the PDI W-hold once worn in, they make the most difference on high-powered guns, I find.

I haven't had the time to try the PDI W-Hold in full detail either, but I did pick up a bunch of a whole bunch of hop up rubbers. I'm hoping to find some time to do a comparo-test in a controlled environment to see if I can figure out which hop ups are best.

Sorry...realized I went off on a tangent from the original A+ inner barrel question and went on about the AG stuff.

Very interested in how this turns out. Also, what knockoff suppressor did you get? I've been eying the VFC but it's a little on the expensive side...