WE m4 Allwin MK18II RAS help
 

like the title says i just need help or to be pointed to the right place to help me put this new front end on my m4 ... never done it ... any help is appreciated

thanks

Ryan

It's easiest if you have the actual Daniel Defence barrel nut wrench, but you can do without. Just make sure you don't damage the notches.

You would apply the collar first, followed by the barrel, and then the barrel nut. Once the barrel nut is tightened down and you've confirmed the outer barrel does not wobble, slide the handguard over the barrel and secure to the collar with the 6 screws. Once secured, attach the bottom portion of the handguard and attach the 4 screws on the sides (two per side.)

Finished.

I have the exact one which I got from Huang, Hitman told him it was compatible with the WE, so he told me, I bought it, however it wasn't the case when I tried to install it.

The first half went in smoothly followed by a lot of friction. I ended up grinding down the first half of the threads in barrel nut.

sorry i have never removed one so im trying to figure out how to remove that first ... and what your saying makes sense but id really like a vid of it being done or something to that effect ...

as well i have the original m4 front sight post to remove but it looks like its attached to the front original ris

thanks for replying ... :) and thanks in advance for your patience lol :P

ok so basicly i have managed to get who ris grip off ... and take the push pins out of the front sight post but the wont budge ... but i dont see anything holding it on .. as well the gas tube is still in place ..

Check for a small grub screw under the sight post.

ah ... found it ... ty .. it was under the sling mount ...

last part .. how do i remove the base of all of that . the part you pull back to remove the front grips covering the barrel ?

You need an AR wrench like this style:

http://www.airsoftparts.ca/store2/in...roducts_id=838

fabsports has them for about $15

all good got it ... thanks :)

LOOOOOOL I don't know why it hasn't worked with Lon but what the hell. It went perfectly smooth for me.

And yes you do need the wrench tool, the one that came with all WE M4's have it can be used.

That King Arms wrench and just about every single other barrel wrench on the market that's marketed as an "AR-15 wrench" "Armalite wrench" etc etc will all be the incorrect tool. It is NOT the correct tool to properly torque down a Daniel Defense barrel nut.

THIS is what you should be using to prevent any damage to the notches:

https://danieldefense.com/rail-syste...er-wrench.html

It *looks* like the spanner end on some Armalite multitools that fit the collar of a collapsible stock, but is not the same dimension. The stock collar is smaller, and as such, you can not get a stock collar spanner to properly engage all three notches on the DD barrel nut. If it's a last resort, you can sort of get a stock collar spanner to work by hooking just one of the three notches on to the DD barrel nut, but you have to be very careful in doing so. You will risk damaging the notches if you slip. The King Arms wrench linked above does NOT have the stock collar spanner end, so it would be useless for this situation.

In my opinion, if you're going to go this route, then you might as well use a punch and hammer and just bash away at the DD collar to attach/remove it, but you will most definitely damage it this way and you still won't be able to get the appropriate amount of torque needed to fully secure it.

hey ... thanks to all who helped .. im glad i did this ... now i know how to replace and barrel and ras system .., but i had to improvise by using a rag and monkey wrench and extreme caution not to damage anything , but all in all it worked out ...

so now that im done i thought id post a pic of the end result .. nothing really fancy but this is the m4 i thought id never have so kind of a big deal to me :)

while im posting this i also want to thank frank at velocity arms for all his patience/help. i cant say enough about them just an awsome place to do buisness with .

so anyways ... here is my new baby ... pretty much everything you see is from velocity arms .

i also have a new charging handle on the way and some troy rail covers and a magpul BAD lever

thanks again for all the help

with appreciation/gratitude

Ryan

Where did you get this from? I tried looking for it but no luck

Got it from Airsoftdepot.ca Canadian dealer.

Even though this was months ago, cujo, does your barrel wobble?