Airsoft Canada

Airsoft Canada (https://airsoftcanada.com/forums.php)
-   Upgrades & Modifications (https://airsoftcanada.com/forumdisplay.php?f=24)
-   -   WETTI/AWSS - M4/SCAR/HK416 - Technical Summary Thread (https://airsoftcanada.com/showthread.php?t=90068)

Daiviet October 14th, 2010 21:22

Quote:

Originally Posted by johan_saint (Post 1332000)
Hi everyone....
Check this out :
YouTube - WE G39C GBB production final.flv
WE G36C

MP5 , L85 , G36C...What the first model that WE will release after M14??
WE is the brand that produce more GBBR type than others, I feel want to sell my 520fps SCAR for this G36C :banghead::banghead::banghead:

Quote:

Originally Posted by shaharov (Post 1332487)
I'll probably keep my scar and by the G36c... Just wont eat for a month ;)

Guys, this isn't a discussion thread, this is a technical problem thread. Take it somewhere else.

Sorry to add more clutter Ty, I know you're going to be doing some more deleting.

MilanWG October 16th, 2010 13:16

I have two quick questions:

1) What is the front sight post on a WE M4A1? Is it an A1 or A2?:
"Models for A1, five-prong (adjusts front and rear) and A2, four-prong."

My font sight post notch is way to low (can barley see it) so I would like to know which is the correct version so I can buy the right tool to adjust the height to the correct level.

2) When installing a real-steel pistol grip on a WE M4A1, how do you deal with the selector spring? In the stock WE pistol grip, there is a little hole drilled into the grip for the spring to sit - but in a real-steel pistol grip there is nothing. Should you just "squish/squeeze" the spring in or attempt to drill a hole similar to the stock WE pistol grip?

c3sk October 16th, 2010 15:04

Quote:

Originally Posted by TALIBANMILAN (Post 1333342)
I have two quick questions:

1) What is the front sight post on a WE M4A1? Is it an A1 or A2?:
"Models for A1, five-prong (adjusts front and rear) and A2, four-prong."

My font sight post notch is way to low (can barley see it) so I would like to know which is the correct version so I can buy the right tool to adjust the height to the correct level.

2) When installing a real-steel pistol grip on a WE M4A1, how do you deal with the selector spring? In the stock WE pistol grip, there is a little hole drilled into the grip for the spring to sit - but in a real-steel pistol grip there is nothing. Should you just "squish/squeeze" the spring in or attempt to drill a hole similar to the stock WE pistol grip?

Not looking at it atm (at work) if I recall it is the A2. If you have some 5.56/7.62 kicking around you can use that to adjust your front sight :)

Real steel pistol grips use the selector tension spring & pin hole.
Example: http://www.brownells.com/.aspx/pid=1...6_BATTLE_GRIP#

http://www.brownells.com/userdocs/pr...71000015_1.jpg

I think some earlier models didn't have it, as the assembly was a bit different. My RS tango down grip does have this hole though (don't forget the lock washer also)


(if it doesn't have it, just drill it!)

Where did you get your RS pistol grip from?

MrEvolution October 16th, 2010 15:22

Quote:

Originally Posted by Sbradshaw (Post 1331771)
so ive installed the ratech upgrade kit minus the hopup unit( not sure how its an upgrade it looks the same as origonal), but to the point... the orings on the ratech set seem to be larger than the origonal orings and are getting stuck. now do i use silicon oil on these or cylinder grease?? and will they eventually wear down?

Quote:

Originally Posted by m102404 (Post 1331857)
Run the bolt in and out until they wear in (might take a long while)...keep them lubed to help it along.

You can either try to find replacement o-rings and trial-error it until you find a nice fit...or (this is up to you to decide to do this) you can take some fine 400/600 grit wet-dry sandpaper and buff them down to size.

I was given the same advice by Tys as well. I have the entire o-ring section covered in white lithium grease. It rarely hangs now.

Tys I plan to reverse that spring tonight, ill let u know how it goes.

KEVORKIAN October 16th, 2010 15:32

Quote:

Originally Posted by TALIBANMILAN (Post 1333342)
I have two quick questions:

2) When installing a real-steel pistol grip on a WE M4A1, how do you deal with the selector spring? In the stock WE pistol grip, there is a little hole drilled into the grip for the spring to sit - but in a real-steel pistol grip there is nothing. Should you just "squish/squeeze" the spring in or attempt to drill a hole similar to the stock WE pistol grip?

Are you sure that you purchased a RS version? I have yet to buy one without the hole and I have the Tango Down, Hogue & Magpul MIAD and they all have it!!!
I did have to enlarge the opening to get it to work properly with the spring in my WE M4, SCAR, PDW and HK 416...if you don't it causes the selector to become notchy & difficult to move!

MilanWG October 16th, 2010 15:34

I have a real TangoDown battle grip in the mail.

c3sk October 16th, 2010 15:39

Quote:

Originally Posted by TALIBANMILAN (Post 1333398)
I have a real TangoDown battle grip in the mail.

Yea man, if it's real - you will have no problems (at least with Tango)

ShelledPants October 16th, 2010 15:40

Yeah, I have a Vietnam era A1 Pistol Grip sitting on my shelf, needs a little bit of dremel to open up the selector switch spring housing to fit.

MilanWG October 16th, 2010 16:39

Awesome. Thanks guys, much appreciated.

Any confirmation on the front sight post - is it A1 or A2?

MrEvolution October 17th, 2010 14:19

Mine is an A2 and has 4 sides (this is what youre asking right?)

MilanWG October 17th, 2010 14:31

Thanks for the info - much appreciated.

MrEvolution October 17th, 2010 23:56

Could someone PLEASE snap a photo of their lower trigger group. I cannot figure out how to install the torsion spring properly (I forget how it looked before :() in a hope to fix my gun.

m102404 October 18th, 2010 06:55

something like this Sam

http://i156.photobucket.com/albums/t...4/DSC_7471.jpg

MrEvolution October 18th, 2010 09:29

Thank you SO MUCH Tys! :)

MrEvolution October 18th, 2010 20:22

Its aliiiiiiiiiiiiiiiive!!!!!!!!!!!!!!!!!!!!!!!!!!

5 mags, no venting.
6th mag was weird because it repeatedly gave off a very faint strike despite having gas in it, and as Murphy would have it, I am out of propane until tomorrow.

Thank you all for your assistance.


All times are GMT -4. The time now is 19:23.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.