Airsoft Canada - My TM Hi-Capa 5.1

Airsoft Canada (https://airsoftcanada.com/forums.php)

- Airsoft Media (https://airsoftcanada.com/forumdisplay.php?f=30)

- - My TM Hi-Capa 5.1 (https://airsoftcanada.com/showthread.php?t=48716)

Quote:

Originally Posted by RacingManiac (Post 892879)

No I have a second Hi-Capa that's being built as an open gun....but I am swapping the trigger setup between them to see how it works on a stock grip....and yes that one is having a C-more mounted....

Ohhhh!. Phew. :p You damn rich maniac!!

or I am damn poor and spending way too much on this...lol

So my Madbull Chrono got here....finally got some testing done to this...

10 shot, using BB Bastard 0.20g, mag at room temp(~68 degree F)
331.8
331.8
334.4
333.1
334.4
336.3
331.8
328.1
326.2
328.1
Average: 331.6

Decent results I guess, don't know if I was expecting more.....

that's pretty good bud, remember it's just an airsoft gun. one with all sorts of crazy ass moving bits and powered by something you can't even hold in your hand. now that your consistency is good, how are your groupings? :P

Quote:

Originally Posted by RacingManiac (Post 589510)

Well still a work in progress, hopefully I can get the Freedom Art kit from Illusion tomorrow so I can update this again in the weekend...but this is it so far...

External:
SD "OPS MRP" Metal Slide
SD "Barsto .45 ACP" Chamber
SD 1911 Threaded Outer Barrel(does not fit exactly thus the longer visible portion outside of the slide, 3rd pic)
SD Hi-Capa Bushing kit
Stock Full Length recoil rod
Nineball Checkered Low Profile Mag Catch
Stock Pistol grip/trigger/mag bumper was sanded to eleminate the shiny plastic look to a duller black.

Internal:
SD Loading Nozzle
SD Aluminum Piston
Guarder High performance valve
Nine Ball Hammer Spring
Enhanced Recoil Spring(unknown brand, got it with the gun)

Not Installed ATM:
PDI 6.05mm Tightbore, for 7" Hi-Capa

To Come:
Freedom Art Government Length Rail frame
Nine Ball Black oval hammer

http://www.supercars.net/pitlane/pic...3/3298238a.jpg

http://www.supercars.net/pitlane/pic...3/3298238b.jpg

http://www.supercars.net/pitlane/pic...3/3298238c.jpg

http://www.supercars.net/pitlane/pic...3/3298238d.jpg

http://www.supercars.net/pitlane/pic...3/3298239d.jpg

Will the SD Hi-Capa Bushing kit fit in a we 1911? Nice gun btw

Don't know, but I am guessing no....

Ditch the lower imitation grip bolt. SVI only uses the upper bolt that secures the grip to the frame. STI uses both.

Other than that, I'm envious of your polishing technique.

Hey RM do you have any gap or play between the hybrid portion of the barrel and the slide? Does it rattle at all?

nope....there is a little bit of play between the frame and the slide, but barrel to slide is play-free....

How's yours?

Quote:

Originally Posted by RacingManiac (Post 996698)

tough critic...lol

fixed:
http://www.pbase.com/racingmaniac/im...4/original.jpg
http://www.pbase.com/racingmaniac/im...5/original.jpg
http://www.pbase.com/racingmaniac/im...6/original.jpg
http://www.pbase.com/racingmaniac/im...7/original.jpg

Must have a hard time getting thos .45s in the gun hey. lol

Quote:

Originally Posted by RacingManiac (Post 996698)

tough critic...lol

fixed:

Aaaaah. much better. I feel relieved, now. lol

I can barely get a piece of paper between the hybrid portion of the barrel and slide.

I had to really tighten up the steel slide to the frame though, it was surprisingly loose (not really bad - but more than I expected since my open gun was so good and tight).

I think I may want to tighten the slide to barrel. But it's so minimal, and so much work lapping that I don't think it's worth doing.

Our Limited guns are like two tone opposite brothers :)

I don't think I can fit a piece of paper between there...the 12mm mill pretty much cut it perfect for the SD barrel...

Do you use a piece of steel stock on the frame rail and hammer it then refinish the frame rail?

Same with my Open gun too, it does seem more secure than the standard one...